MODEL G0605X/G0606XEXTREME SERIES 12" TABLE SAWOWNER'S MANUALCOPYRIGHT © OCTOBER, 2006 BY GRIZZLY INDUSTRIAL, INC.WARNING: NO PORTION OF THI
-8-G0605X/G0606X Extreme Series 12" Table Saw7. NEVER OPERATE MACHINERY WHEN TIRED OR UNDER THE INFLUENCE OF DRUGS OR ALCOHOL. Be mentally al
G0605X/G0606X Extreme Series 12" Table Saw-9-Like all machines there is danger associated with the Model G0605X/G0606X. Accidents are freque
-10-G0605X/G0606X Extreme Series 12" Table SawBelow are tips to avoid the most common causes of kickback:• Only cut workpieces with at le
G0605X/G0606X Extreme Series 12" Table Saw-11-The following is a list of common definitions, terms and phrases used throughout this manual as the
-12-G0605X/G0606X Extreme Series 12" Table SawSerious personal injury could occur if you connect the machine to the power source befo
G0605X/G0606X Extreme Series 12" Table Saw-13-In the event of an electrical short, grounding reduces the risk of electric shock. The
-14-G0605X/G0606X Extreme Series 12" Table SawWear safety glasses dur-ing the entire set up pro-cess!This machine presents serious injury haz
G0605X/G0606X Extreme Series 12" Table Saw-15-Machine InventoryThe following components are included with each G0605X/G0606X. After all the p
-16-G0605X/G0606X Extreme Series 12" Table SawOutfeed Table InventoryBox Contents: (Figure 10) QtyA. Outfeed Table ...
G0605X/G0606X Extreme Series 12" Table Saw-17-Hardware Recognition Chart
-18-G0605X/G0606X Extreme Series 12" Table SawFigure 11. Minimum working clearances.Floor LoadRefer to the Machine Data Sheet for the weight and
G0605X/G0606X Extreme Series 12" Table Saw-19-Extension Table2. Fasten the rear rail to the table with five cap screws and lock washers as shown
-20-G0605X/G0606X Extreme Series 12" Table Saw5. While an assistant holds the extension table, fasten the front rail to the extension table with
G0605X/G0606X Extreme Series 12" Table Saw-21-Outfeed TableComponents and Hardware Needed: QtyOutfeed Table ...
-22-G0605X/G0606X Extreme Series 12" Table Saw3. Place the extension table assembly upright with the feet on the ground, align the slots in
G0605X/G0606X Extreme Series 12" Table Saw-23-Table InsertYou MUST install the table insert before operating the table saw.Components and Hardwar
-24-G0605X/G0606X Extreme Series 12" Table SawBracketRiving KnifeLeverRiving KnifeYou MUST install the riving knife or the splitter and b
G0605X/G0606X Extreme Series 12" Table Saw-25-Figure 31. Switch installed.Figure 32. Miter gauge installed.WasherHandle2. Slide the miter gau
-26-G0605X/G0606X Extreme Series 12" Table SawThe adjustments listed below have been per-formed at the factory and no further setup
G0605X/G0606X Extreme Series 12" Table Saw-27-4. Remove all tools and foreign objects from the machine. 5. Connect the tablesaw to the p
Table of ContentsINTRODUCTION ...
-28-G0605X/G0606X Extreme Series 12" Table SawOperation SafetySECTION 4: OPERATIONSBasic ControlsThe basic controls for the table saw are shown i
G0605X/G0606X Extreme Series 12" Table Saw-29-Disabling On/Off SwitchTo disable the switch and prevent accidental startup, insert the safet
-30-G0605X/G0606X Extreme Series 12" Table SawLaminate blade features: • Best for cutting plywood or veneer.• 40-80 teeth. • Triple chip tooth
G0605X/G0606X Extreme Series 12" Table Saw-31-To make a rip cut:1. Review Preventing Kickback on Page 10 and take the necessary precauti
-32-G0605X/G0606X Extreme Series 12" Table Saw"Crosscutting" means cutting across the grain of the workpiece. In MDF or particleb
G0605X/G0606X Extreme Series 12" Table Saw-33-Miter CutsA miter is an angled crosscut. Miters are usually cut in the same manner as crosscut
-34-G0605X/G0606X Extreme Series 12" Table SawCommonly used in furniture joinery, a dado is a straight channel cut in the face of the workpiece
G0605X/G0606X Extreme Series 12" Table Saw-35-Figure 48. Single-blade dado first cut.7. Reconnect the saw to the power source and turn the saw O
-36-G0605X/G0606X Extreme Series 12" Table SawCommonly used in furniture joinery, a rabbet is an L-shaped groove cut in the edge of the workpiece
G0605X/G0606X Extreme Series 12" Table Saw-37-To cut rabbets with the standard blade:Note: Cutting rabbets with a standard saw blade DOES NOT req
SECTION 5: ACCESSORIES ... 41SECTION 6: MAINTENA
-38-G0605X/G0606X Extreme Series 12" Table SawResawingResawing is the process of cutting a thick piece of stock into one or more thinner pieces.
G0605X/G0606X Extreme Series 12" Table Saw-39-Figure 55. Clamping the resawing barrier.4. Secure the joint with the wood screws.Auxiliary FenceT
-40-G0605X/G0606X Extreme Series 12" Table SawTo perform resawing operations:1. DISCONNECT THE SAW FROM POWER!2. Remove the standard table
G0605X/G0606X Extreme Series 12" Table Saw-41-Figure 59. G7895 Citrus Degreaser.G7895—Citrus DegreaserThis citrus based degreaser is perfect for
-42-G0605X/G0606X Extreme Series 12" Table SawFigure 62. Half-mask respirator and disposable cartridge filters.H2499—Small Half-Mask RespiratorH3
G0605X/G0606X Extreme Series 12" Table Saw-43-Figure 67. G3445 Precision Saw Tool.G3445—Precision Saw ToolThis high impact plastic Saw Aid™ quick
-44-G0605X/G0606X Extreme Series 12" Table SawCleaning the Model G0605X/G0606X is relatively easy. Vacuum excess wood chips and sawdust, and
G0605X/G0606X Extreme Series 12" Table Saw-45-Review the troubleshooting and procedures in this section to fix your machine if a problem develops
-46-G0605X/G0606X Extreme Series 12" Table SawTable Saw OperationsSymptom Possible Cause Possible SolutionMachine has vibra-tion or noisy op
G0605X/G0606X Extreme Series 12" Table Saw-47-Replacing Flat BeltTo ensure optimum power transmission from the motor to the blade, the flat belt
G0605X/G0606X Extreme Series 12" Table Saw-3-If you have any comments regarding this manual, please write to us at the address below:Grizzly Indu
-48-G0605X/G0606X Extreme Series 12" Table Saw9. Lower the arbor down all the way, remove the button head cap screws on the lower part of
G0605X/G0606X Extreme Series 12" Table Saw-49-Blade Tilt StopsThe table saw features stop bolts that stop the blade exactly at 45° and 90
-50-G0605X/G0606X Extreme Series 12" Table SawFigure 77. 45° stop bolt and jam nut.45° Stop BoltJam Nut5. Continue adjusting the stop bolt un
G0605X/G0606X Extreme Series 12" Table Saw-51-Miter Slot to BladeParallelism3. With the end of the adjustable square just touching the
-52-G0605X/G0606X Extreme Series 12" Table SawFigure 82. Shim procedure diagram A.Figure 83. Shim procedure diagram B.8. Tilt the blade to 45° a
G0605X/G0606X Extreme Series 12" Table Saw-53-Blade AlignmentIf the blade contacts the table insert when raised or tilted, the blade must be alig
-54-G0605X/G0606X Extreme Series 12" Table SawMiter GaugeTools Needed QtyHex Wrench 2.5mm ...1Phillips H
G0605X/G0606X Extreme Series 12" Table Saw-55-Service PerformedApproximate Hours Of UseService LogDate
-56-G0605X/G0606X Extreme Series 12" Table SawG0605X/G0606X Electrical ComponentsFigure 88. G0605X motor junction box.Figure 91. G0605X/G0606X di
G0605X/G0606X Extreme Series 12" Table Saw-57-
-4-G0605X/G0606X Extreme Series 12" Table SawMODEL G0605X 12" EXTREME SERIES TABLE SAWCustomer Service #: (570) 546-9663 • To Order Call: (8
-58-G0605X/G0606X Extreme Series 12" Table SawG0606X Electrical ComponentsFigure 93. G0606X magnetic switch prewired to 220V, 3-phase.Figure 94.
G0605X/G0606X Extreme Series 12" Table Saw-59-G0606X Wiring Diagram 220V440V WIRING
-60-G0605X/G0606X Extreme Series 12" Table SawG0606X Wiring Diagram 440V
G0605X/G0606X Extreme Series 12" Table Saw-61-Cabinet, Motor & Main Table Breakdown
-62-G0605X/G0606X Extreme Series 12" Table SawCabinet, Motor & Main Table Parts ListREF PART # DESCRIPTION REF PART # DESCRIPTION6 P0605X006
G0605X/G0606X Extreme Series 12" Table Saw-63-REF PART # DESCRIPTION REF PART # DESCRIPTION75-8 P0606X075-8 FUSE (G0606X) 111-1 P0606X111-1 MOTOR
-64-G0605X/G0606X Extreme Series 12" Table Saw
G0605X/G0606X Extreme Series 12" Table Saw-65-Fence Assembly Breakd
-66-G0605X/G0606X Extreme Series 12" Table SawMiter Gauge Assembly BreakdownREF PART # DESC
G0605X/G0606X Extreme Series 12" Table Saw-67-
G0605X/G0606X Extreme Series 12" Table Saw-5-MODEL G0606X 12" EXTREME SERIES TABLE SAWCustomer Service #: (570) 546-9663 • To Order Call: (8
-68-G0605X/G0606X Extreme Series 12" Table Saw
G0605X/G0606X Extreme Series 12" Table Saw-69-Warning Label Parts ListSafety labels warn about machine hazards and ways to prevent injury. The ow
-70-G0605X/G0606X Extreme Series 12" Table SawGrizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original pur
-6-G0605X/G0606X Extreme Series 12" Table SawFigure 1. G0606X identification.A. Front RailB. Outfeed TableC. Blade Guard and SplitterD. Miter
G0605X/G0606X Extreme Series 12" Table Saw-7-Safety Instructions for Machinery4. ALWAYS WEAR A NIOSH APPROVED RESPIRATOR WHEN OPERATING MA
Comments to this Manuals