MODEL G0463SMALL MILL/DRILLOWNER'S MANUALCOPYRIGHT © NOVEMBER, 2005 BY GRIZZLY INDUSTRIAL, INC. REVISED DECEMBER 2007.WARNING: NO PORTION OF THIS
-8-G0463 Small Mill/Drill7. ONLY ALLOW TRAINED AND PROP-ERLY SUPERVISED PERSONNEL TO OPERATE MACHINERY. Make sure operation instructions a
G0463 Small Mill/Drill-9-Additional Safety for Mill/Drills1. UNDERSTANDING CONTROLS. Make sure you understand the use and operation of all controls.2
-10-G0463 Small Mill/DrillFigure 2. A 5-15 plug and receptacle.Serious personal injury could occur if you connect the machine to the power
G0463 Small Mill/Drill-11-The Model G0463 was carefully packed when it left our warehouse. If you discover the machine is damaged after you hav
-12-G0463 Small Mill/DrillInventoryAfter all the parts have been removed from the two boxes, you should have the following items:Box 1: (Figu
G0463 Small Mill/Drill-13-Workbench LoadAlthough adjustable feet are included with your mill/drill, It is strongly recommended you bolt your mac
-14-G0463 Small Mill/DrillMounting to WorkbenchThe Model G0463 should be bolted to a work-bench to provide maximum rigidity and safety.Compone
G0463 Small Mill/Drill-15-Test Run and Spindle Break-inThe Model G0463 has two speed ranges: Low range is 0–1000; high range is 0–2000 RPM. It
-16-G0463 Small Mill/DrillFigure 9. Striking the drawbar.Drill Chuck RemovalThe Model G0463 may have shipped with the drill chuck installed in the spi
G0463 Small Mill/Drill-17-The Model G0463 features an R-8 spindle taper, which only accepts R-8 collets. R-8 collets come in many sizes, typically
Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine MUST maintain the original location and readability of
-18-G0463 Small Mill/DrillDamage to your eyes, lungs, and ears could result from using this machine without proper protective gear. Always we
G0463 Small Mill/Drill-19-Power ShutdownIt is important to shut the power OFF when the mill/drill is not in use. Leaving the power ON
-20-G0463 Small Mill/DrillFigure 14. Table locks.Table TravelThe mill/drill table can be moved in the X and Y axis.Longitudinal FeedThe longitudinal
G0463 Small Mill/Drill-21-Setting RPMClosely follow the proper cutting speed and prop-er feed to reduce undue strain on all moving parts and for opera
-22-G0463 Small Mill/DrillSECTION 5: ACCESSORIESACCESSORIESG9002—21⁄2" Swivel Base Milling ViseG5971— 31⁄2" Swivel Base Milling ViseG5972—4&
G0463 Small Mill/Drill-23-Figure 21. G2861 Face mill.G2861—21⁄2" Face MillThis 21⁄2" Face Mill accepts four carbide inserts. Comes with an R
-24-G0463 Small Mill/DrillSECTION 6: MAINTENANCEAlways disconnect power to the machine before performing maintenance. Failure to do this may re
G0463 Small Mill/Drill-25-Review the troubleshooting and procedures in this section to fix your machine if a problem develops. If you need replacement
-26-G0463 Small Mill/DrillAdjusting GibsFigure 27. Gib adjustment.The function of the gibs is to take out play in the table, and cross slide, and colu
G0463 Small Mill/Drill-27-Electrical ComponentsFigure 30. Circuit board.Figure 31. Equipment grounds.Figure 35. Main power switch.Figure 33. RPM contr
Table of ContentsINTRODUCTION ...
-28-G0463 Small Mill/DrillWiring Diagram
G0463 Small Mill/Drill-29-
-30-G0463 Small Mill/Drill
G0463 Small Mill/Drill-31-REF PART # DESCRIPTION REF PART # DESCRIPTION1 P0463001 TRANSMISSION GEAR 51 P0463051 DIAL FORK SHAFT2 P0463002 DIAL FORK 52
-32-G0463 Small Mill/DrillREF PART # DESCRIPTION REF PART # DESCRIPTION99 PK30M KEY 4 X 4 X 25 150 PRP39M ROLL PIN 4 X 20100 PK34M KEY 5 X 5 X 20 151
G0463 Small Mill/Drill-33-Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine MUST maintain the original lo
-34-G0463 Small Mill/DrillGrizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of p
SECTION 4: OPERATIONS ... 18Operation Safety .
G0463 Small Mill/Drill-3-If you have any comments regarding this manual, please write to us at the address below:Grizzly Industrial, Inc.C/O Technical
-4-G0463 Small Mill/DrillProduct Dimensions:Weight...
G0463 Small Mill/Drill-5-Main Specifications:Spindle Travel...
-6-G0463 Small Mill/DrillFigure 1. G0463 Identification.A. Emergency Stop Button B. Drawbar (under cover)C. High/Low Gear Change KnobD. Headstock
G0463 Small Mill/Drill-7-4. ALWAYS USE HEARING PROTECTION WHEN OPERATING MACHINERY. Machinery noise can cause permanent hearing damage. 5.
Comments to this Manuals