1 HP DUST COLLECTORMODEL G8027INSTRUCTION MANUALCOPYRIGHT © MAY, 2005 BY GRIZZLY INDUSTRIAL, INC.WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED
-8- G8027 1 HP Dust CollectorFigure 2. Typical type 5-15 plug and receptacle.Serious personal injury could occur if you connect the machine t
G8027 1 HP Dust Collector -9-Your machine left our warehouse in two care-fully packed boxes. If you discover the machine is damaged after
-10- G8027 1 HP Dust CollectorAfter all the parts have been removed from the two boxes, you should have the following items:Box Components (Fi
Hardware Recognition Chart
-12- G8027 1 HP Dust CollectorComponents and Hardware Needed: QtyMotor/Impeller Housing ...1Collector ...
G8027 1 HP Dust Collector -13-5. Install the rubber gasket onto the motor/impeller housing opening. 6. Install the collector onto the mot
-14- G8027 1 HP Dust CollectorCollection and Filtration BagsComponents and Hardware Needed: QtyCollection Bag ...
G8027 1 HP Dust Collector -15-GeneralThe Model G8027 is designed to be a single-machine dust collector. Locate the dust collec-tor where
-16- G8027 1 HP Dust CollectorEnsure that the entire system is grounded. If using plastic blast gates to direct air flow, the grounding
G8027 1 HP Dust Collector -17-Once assembly is complete and adjustments are done to your satisfaction, you are ready to test run the machine.T
WARNINGSome dust created by power sanding, sawing, grind-ing, drilling, and other construction activities contains chemicals known to the State o
-18- G8027 1 HP Dust CollectorSECTION 5: ACCESSORIESFigure 19. Our most popular safety glasses.G7984—Face ShieldH1298—Dust Sealed Safety GlassesH1300—
G8027 1 HP Dust Collector -19-G2525—Dust Collection BasicsThis incisive book skillfully guides the wood-worker through all the steps necessary in the
-20- G8027 1 HP Dust CollectorSince all bearings are shielded and permanently lubricated, simply leave them alone until they need to be replaced
G8027 1 HP Dust Collector -21-To empty the collection bag:1. Make sure you are wearing a respirator and the dust collector is unplugged.2. Un-clamp
-22- G8027 1 HP Dust CollectorSYMPTOM POSSIBLE CAUSE CORRECTIVE ACTIONMotor will not start, or it growls on start up.1. Power supply fuse or circuit
G8027 1 HP Dust Collector -23-Electrical Components and Wiring110V Power CordGround (Green)MotorBlack WireMotor WiresON/OFFSwitchGREEN(GROUND)TO 110 V
-24- G8027 1 HP Dust Collector3325412341242323027282913544013204039263818-41835171634134021191476981013121136312233229518-142434745464448UNPLUG POWERA
REF PART # DESCRIPTION REF PART # DESCRIPTION1 P8027001 SWIVEL CASTER 23 P8027023 COLLECTOR2 PS20M PHLP HD SCR M5-.8 X 15 24 P8027024 COLLECTION BAG3
WARRANTY AND RETURNS-26- G8027 1 HP Canister Dust CollectorGrizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the orig
CUT ALONG DOTTED LINEName _____________________________________________________________________________ Street ______________________________________
Table of ContentsINTRODUCTION ...
TAPE ALONG EDGES--PLEASE DO NOT STAPLEFOLD ALONG DOTTED LINEFOLD ALONG DOTTED LINEGRIZZLY INDUSTRIAL, INC.P.O. BOX 2069BELLINGHAM, WA 98227-2069Place
Buy Direct and Save with Grizzly® – Trusted, Proven and a Great Value!-OR-• SECURE ORDERING• ORDERS SHIPPED WITHIN 24 HOURS• E-MAIL RESPONSE WITHIN O
-2- G8027 1 HP Dust CollectorIf you have any comments regarding this manual, please write to us at the address below:Grizzly Industrial, Inc.C/O Techn
G8027 1 HP Dust Collector -3-Customer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901MODEL G8027 1 HP DUST COLLECTOR
-4- G8027 1 HP Dust Collector1. Upper Bag Support Rod2. Filtration Bag3. Collector4. Collection Bag5. Collection Bag Support RodIdentification6.
G8027 1 HP Dust Collector -5-4. ALWAYS USE HEARING PROTECTION WHEN OPERATING MACHINERY. Machinery noise can cause permanent hearing damage.
-6- G8027 1 HP Dust Collector7. ONLY ALLOW TRAINED AND PROP-ERLY SUPERVISED PERSONNEL TO OPERATE MACHINERY. Make sure operation instructio
G8027 1 HP Dust Collector -7-6. AVOIDING FIRES. DO NOT allow steel to strike against impeller, which may pro-duce a spark. Sparks can smol
Comments to this Manuals