TENONING JIGMODEL H7583INSTRUCTION MANUALCOPYRIGHT © MAY, 2005 BY GRIZZLY INDUSTRIAL, INC. REVISED DECEMBER, 2007 (JB)WARNING: NO PORTION OF THIS MANU
-8-H7583 Tenoning JigThe unpainted surfaces are coated with a waxy oil to protect them from corrosion during ship-ment. Remove this protective
H7583 Tenoning Jig-9-Figure 2. Partial assembly.In this procedure you will assemble the tenoning jig. The guide bar is initially in position on the ji
-10-H7583 Tenoning JigFigure 7. Guide bar locations.Button Head ScrewLeft-Tilt Saw LocationRight-Tilt Saw LocationJig Setup for a Left-Tilt Table Saw
H7583 Tenoning Jig-11-Figure 8. Miter slot guide bar.Guide BarIn this procedure you will adjust the guide bar so there is minimal play between the mit
-12-H7583 Tenoning JigFigure 10. Blade clearance adjustment.Figure 11. Blade parallelism.Jam Nutand Positive StopIn this procedure you will adjust the
H7583 Tenoning Jig-13-10. Rotate the micro-adjustment knob until the major adjustment sleeve extends 11⁄2" out of the jig, or approximately
-14-H7583 Tenoning JigDamage to your eyes, lungs, and ears could result from using this jig without proper protective gear. Always wear safety g
H7583 Tenoning Jig-15-2. Plane a wood base stop to the thickness of the tenoning jig base, and mount it to the front of the table saw as show
-16-H7583 Tenoning JigMAKE SURE the blade clearance is adjusted correctly! DO NOT adjust the work support plate any closer than 1⁄8" from the saw
H7583 Tenoning Jig-17-Figure 22. First structural cheek cut.B. Cutting Tenon Cheeks:The tenon uses two styles of cheeks, structural and cosmeti
WARNINGSome dust created by power sanding, sawing, grind-ing, drilling, and other construction activities contains chemicals known to the State
-18-H7583 Tenoning JigFigure 26. Cutting the shoulder.C. Cutting Tenon Shoulders:The final set of cuts are two structural shoulder cuts and tw
H7583 Tenoning Jig-19-Always disconnect power to the machine before performing maintenance. Failure to do this may result in serious person-al
-20-H7583 Tenoning Jig
H7583 Tenoning Jig-21-Parts ListREF PART # DESCRIPTION REF PART # DESCRIPTION1 PH7583001 LOCK LEVER M8-1.25 34-3 PH7583034-3 FLAT HD SCR 1/4-28 X 5/16
-22-H7583 Tenoning JigGrizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purch
CUT ALONG DOTTED LINEName _____________________________________________________________________________ Street ______________________________________
TAPE ALONG EDGES--PLEASE DO NOT STAPLEFOLD ALONG DOTTED LINEFOLD ALONG DOTTED LINEGRIZZLY INDUSTRIAL, INC.P.O. BOX 2069BELLINGHAM, WA 98227-2069Place
Buy Direct and Save with Grizzly® – Trusted, Proven and a Great Value!-OR-• SECURE ORDERING• ORDERS SHIPPED WITHIN 24 HOURS• E-MAIL RESPONSE WITHIN O
Table of ContentsINTRODUCTION ...
-2-H7583 Tenoning JigCustomer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901MACHINE DATA SHEETCapacities: Maximum
H7583 Tenoning Jig-3-IdentificationA. Adjustable Clamp AssemblyB. Back StopC. Clamp Slide Lock BoltD. Clamp CrankE. Clamp Slide Lock BoltF. Back
-4-H7583 Tenoning Jig4. ALWAYS USE HEARING PROTECTION WHEN OPERATING MACHINERY. Machinery noise can cause permanent hearing damage. 5. WEAR
H7583 Tenoning Jig-5-7. ONLY ALLOW TRAINED AND PROP-ERLY SUPERVISED PERSONNEL TO OPERATE MACHINERY. Make sure operation instructions are s
-6-H7583 Tenoning JigSafety Instructions for the Tenoning Jig7. ADJUSTING JIG. Unplug the table saw before installing or adjusting the jig, saw,
H7583 Tenoning Jig-7-The Model H7583 was carefully packed when it left our warehouse. If you discover the machine is damaged after you have
Comments to this Manuals