HHuunntteerr’’ss MMeeaatt CCuuttttiinngg BBaannddssaaww -- 11 --HUNTER’S MEAT CUTTING SAWMODEL G1016INSTRUCTION MANUALCOPYRIGHT © 1995 BY GRIZZLY
A. StandNote: All die-cut metal parts have a sharpedge (called “flashing”) on them after they areformed. This is removed at the factory.Sometimes, th
- 8 - Hunters Meat CuttingBandsaw7. If the stand is wobbly, check your floorfirst. If the floor is level, loosen the boltsand wiggle the stand until i
VII. AssemblyHunter’s Meat Cutting Bandsaw - 9 -1"Driven PulleyMotor PulleyFigure 4 shows the V-Belt installed correctly.D. Pulleys and V-BeltPu
- 10 - Hunters Meat CuttingBandsawE. TableBefore installing the table andguards, peel off the blue, protectiveplastic.Slide the table on at a 45° angl
Hunter’s Meat Cutting Bandsaw - 11 -G. Meat GrinderTo install the meat grinder (Figure 8):1. Loosen the mounting bolt at the base ofthe meat grinder.2
- 12 - Hunters Meat CuttingBandsawA. Blade TensionTo check blade tension:1. Turn off the power and unplug the saw.2. Remove the upper wheel guard byre
Hunter’s Meat Cutting Bandsaw - 13 -To CHECK tracking:1. Turn the power off and unplug the saw.2. Spin the wheels through several com-plete rotations
- 14 - Hunters Meat CuttingBandsawVIII. AdjustmentsFigure 13 shows a closeup of the upper guideassembly. To adjust the lower guide tabs(Figure 14):1.
Hunter’s Meat Cutting Bandsaw - 15 -VIII. AdjustmentsTo adjust the lower support bearing(Figure 14):1. Loosen the nut that holds the lower sup-port b
- 16 - Hunters Meat Cutting BandsawVIII. AdjustmentsF. Blade GuardWarning: The blade guard must cover all ofthe blade above the upper blade guideass
Table of ContentsPAGEI. Introduction...1II. Saf
Hunter’s Meat Cutting Bandsaw - 17 -1. Ensure that the machine sits firmly on thefloor before use. Any “wobbles” must becorrected before operation.2.
- 18 - Hunters Meat Cutting BandsawA. General1. Use a sharp, high-quality blade. 2. Use the right blade for the job.Your saw comes equipped with a “bo
Your meat cutting band-saw MUST be thoroughlycleaned after each use!Bacterial infection is a major concern whenworking with raw meat. Your meat cuttin
- 20 - Hunters Meat CuttingBandsawSince the moving parts on this machine runon shielded ball bearings, you will find thatthere is very little in the l
Hunter’s Meat Cutting Bandsaw - 21 -XIII. TroubleshootingSYMPTOMMotor will not start.Motor will not start; fuses orcircuit breakers blow.Motor fails t
- 22 - Hunter’s Meat Cutting BandsawA403536577059656660643535232138046262564631913725881812116856173241361636263604864-1757923505757445743839437139421
Hunter’s Meat Cutting Bandsaw - 23 -223130323333B33A7434142937621A2028OPTIONALXV. Meat Grinder Parts Diagram
- 24 - Hunter’s Meat Cutting Bandsaw103102106101111116116120116116116116131129130118117104118118117117118117118117125125117117118118118121117117124123
Hunter’s Meat Cutting Bandsaw - 25 -061 P1016061 BEARING GUIDE SHAFT062 P6000 BEARING 6000-2RS063 PR01M SNAP RING 10mm064 P1016064 GUIDE BLOCK64-1 P10
- 26 - Hunters Meat Cutting BandsawXVIII. Machine DataHUNTER’S MEAT CUTTING SAWDesign Type ...
Table of ContentsPAGEVIII. Adjustments ...12A. Blad
HHuunntteerr’’ss MMeeaatt CCuuttttiinngg BBaannddssaaww -- 2277 --Limited Warranty & Returns PolicyGrizzly Imports, Inc. warrants every produ
We are proud to offer the Hunter’s MeatCutting Bandsaw. When used according tothe guidelines stated in this manual, you canexpect years of trouble-fre
II. Safety Rules for all Tools- 2 - Hunters Meat Cutting Bandsaw1. KNOW YOUR POWER TOOL. Readthe owner’s manual carefully. Learn thetool’s application
II. Safety Rules for all ToolsHunter’s Meat Cutting Bandsaw - 3 -18. NEVER STAND OR LEAN ONTOOL. Serious injury could occur if thetool is tipped or if
- 4 - Hunters Meat CuttingBandsawIf you are unsure about connecting yourbandsaw, don’t take chances: consult theservice dept or a licensed electrician
V. UnpackingIV. Site PlanningHunter’s Meat Cutting Bandsaw - 5 -The bandsaw is shipped from the factory in acarefully packed carton. If you find the
VI. Piece Inventory- 6 - Hunters Meat CuttingBandsawWith all the parts removed from thecontainer, you should have:• Bandsaw Unit with Blade• Motor • M
Comments to this Manuals