Grizzly G0622 User Manual download pdf (Page 34)

-32-

Model G0622 (Mfg 2/08+)

SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION

Machine is loud when

cutting or bogs down in

the cut.

1. Excessive feed rate.

2. The blade TPI is too great, or the

material is too coarse.

1. Refer to Feed Rate on Page 24, or Blade Speed

on Page 25 and adjust as required.

2. Refer to Blade Selection on Page 26 and adjust as

required.

Blades break often. 1. The workpiece is loose in the vise.

2. The feed or cut speed is wrong.

3. The blade TPI is too great, or the

material is too coarse.

4. The blade is rubbing on the wheel

flange.

5. The bandsaw is being started with

the blade resting on the workpiece.

6. The guide bearings are

misaligned, or the blade is rubbing

on the wheel flange.

7. The blade is too thick, or the

blades are of low quality.

1. Clamp the workpiece tighter, or use a jig to hold the

workpiece.

2. Refer to Feed Rate on Page 24, or Blade Speed

on Page 25 and adjust as required.

3. Refer to Blade Selection on Page 26 and adjust as

required.

4. Refer to Blade Tracking on Page 34, and adjust as

required.

5. Start bandsaw and then slowly lower the headstock

by setting the feed rate.

6. Refer to Blade Tracking on Page 34, or Blade

Guides on Page 24, and adjust as required.

7. Use a higher quality blade.

Blade dulls prematurely. 1. The cutting speed is too fast.

2. The blade TPI is too coarse.

3. The blade feed pressure is too

light.

4. The workpiece has hard spots,

welds, or scale is on the material.

5. The blade is twisted.

6. The blade is slipping on the

wheels.

1. Refer to Blade Speed on Page 25 and adjust as

required.

2. Refer to Blade Selection on Page 26 and adjust as

required.

3. Refer to Feed Rate on Page 24, and adjust as

required.

4. Increase the feed pressure, and reduce the cutting

speed.

5. Replace the blade.

6. Refer to Blade Tension on Page 35, and adjust as

required.

Blade wears on one side. 1. The blade guides are worn or mis-

adjusted.

2. The blade guide slide bracket is

loose.

3. The wheels are out of alignment.

1. Refer to Blade Guides on Page 24 and replace or

adjust.

2. Tighten the blade guide bracket.

3. Refer to Blade Tracking on Page 34, and adjust as

required.

Teeth are ripping from the

blade.

1. The feed pressure is too heavy

and the blade speed is too slow; or

the blade TPI is too coarse for the

workpiece.

2. The workpiece is vibrating in the

vise.

3. The blade gullets are loading up

with chips.

1. Refer to Blade Selection on Page 26 and decrease

the feed pressure. Refer to Feed Rate on Page 24,

and adjust as required.

2. Re-clamp the workpiece in the vise, and use a jig if

required.

3. Use a coarser-tooth blade.

The cuts are crooked. 1. The feed pressure is too high.

2. The guide bearings are out of

adjustment, or too far away from

the workpiece.

3. The blade tension is low.

4. The blade is dull.

5. The blade speed is wrong.

1. Refer to Feed Rate on Page 24, and adjust as

required.

2. Refer to Blade Guides on Page 24 and replace or

adjust.

3. Refer to Blade Tension on Page 35, and adjust as

required.

4. Refer to Blade Change on Page 33 and replace

the blade.

5. Refer to Blade Speed on Page 25 and adjust as

required.

1 2 ... 29 30 31 32 33 34 35 36 37 38 39 ... 47 48

Comments to this Manuals

No comments

Grizzly G0622 User Manual Page 34

Comments to this Manuals

Related products and manuals for Power saws Grizzly G0622