Grizzly G0640X User Manual Page 11
- Page / 64
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
G0640X 17" Wood/Metal Bandsaw
-9-
SECTION 2: CIRCUIT REQUIREMENTS
220V Operation
Full Load Amperage Draw
This machine draws the following amps under
maximum load:
Amp Draw ................................................8 Amps
Power Supply Circuit Requirements
You MUST connect your machine to a grounded
circuit that is rated for the amperage given below.
Never replace a circuit breaker on an existing cir
-
cuit with one of higher amperage without consult
-
ing a qualified electrician to ensure compliance
with wiring codes
. If you are unsure about the
wiring codes in your area or you plan to con
-
nect your machine to a shared circuit, consult
a qualified electrician.
Minimum Circuit Size .............................
15 Amps
Extension Cords
Using extension cords may reduce the life of the
motor. Instead, place the machine near a power
source. If you must use an extension cord:
• Use at least a 14 gauge cord that does not
exceed 50 feet in length!
• The extension cord must also have a ground
wire and plug pin.
• A qualified electrician MUST size cords over
50 feet long to prevent motor damage.
Figure 1. NEMA 6-15 plug and receptacle.
Serious personal injury could occur if you
connect the machine to power before com
-
pleting the setup process. DO NOT connect
the machine to the power until instructed
later in this manual.
Electrocution or fire could
result if machine is not
grounded and installed in
compliance with electrical
codes. Compliance MUST
be verified by a qualified
electrician!
Power Connection Device
The type of plug required to connect your machine
to power depends on the type of service you cur
-
rently have or plan to install. We recommend
using the plug shown in Figure
1.
- MODEL G0640X 1
- 17" WOOD/METAL BANDSAW 1
- Table of Contents 3
- INTRODUCTION 4
- Identification 5
- 6
- 8
- 220V Operation 11
- SECTION 3: SETUP 12
- Inventory 13
- Clean Up 14
- Site Considerations 14
- Moving & Placing 15
- Mounting 15
- Assembly 16
- Blade Tension 19
- Test Run 20
- Blade Tensioning 21
- Adjusting Blade 22
- Adjusting Support 23
- Bearings 23
- 0.016'' 23
- Adjusting Positive 24
- Aligning Table 25
- Aligning Fence Miter Gauge 26
- SECTION 4: OPERATIONS 27
- Table Tilt 28
- Quick Release Blade 28
- Blade Terminology 29
- Blade Selection 29
- Tooth Style 30
- Tooth Set 30
- Tooth Pitch 30
- Blade Breakage 31
- Blade Care & 31
- Break-In 31
- Blade Changes 32
- 33
- SECTION 5: WOOD CUTTING 34
- Crosscutting 35
- Resawing 36
- Cutting Curves 37
- Stacked Cuts 37
- Cutting Circles 37
- SECTION 6: METAL CUTTING 38
- SECTION 7: ACCESSORIES 41
- SECTION 8: MAINTENANCE 43
- Guide Post Gears 44
- Redressing Rubber 45
- SECTION 9: SERVICE 46
- Cutting Operations 47
- Miscellaneous 47
- Replacing V-Belts 48
- Adjusting Wheel 48
- Wheel Alignment 49
- Coplanarity Gauge 50
- Shimming Table Blade Lead 51
- Adjusting Tension 52
- Electrical Component Wiring 53
- Wiring Diagram 54
- Parts List 57
- 61
- 62
- WARRANTY AND RETURNS 63
- 64
- 64
Related products and manuals for Power saws Grizzly G0640X
Power saws Grizzly G1023SL User Manual
(50 pages)
(50 pages)
Power saws Grizzly G0524 User Manual
(60 pages)
(60 pages)
Power saws Grizzly H3390 User Manual
(35 pages)
(35 pages)
Power saws Grizzly G0606X1 User Manual
(12 pages)
(12 pages)
Power saws Grizzly G0506 User Manual
(56 pages)
(56 pages)
Power saws Grizzly G0561 User Manual
(52 pages)
(52 pages)
Power saws Grizzly G0664 User Manual
(2 pages)
(2 pages)
Power saws Grizzly G0555 User Manual
(55 pages)
(55 pages)
Power saws Grizzly G8994 User Manual
(14 pages)
(14 pages)
Power saws Grizzly G0501 User Manual
(96 pages)
(96 pages)
Power saws Grizzly G1060 User Manual
(22 pages)
(22 pages)
Power saws Grizzly G0659 User Manual
(60 pages)
(60 pages)
Power saws Grizzly G7212 User Manual
(5 pages)
(5 pages)
Power saws Grizzly G0651 User Manual
(104 pages)
(104 pages)
Power saws Grizzly G0622 User Manual
(48 pages)
(48 pages)
Power saws Grizzly G1148 User Manual
(27 pages)
(27 pages)
Power saws Grizzly G0614 User Manual
(68 pages)
(68 pages)
Power saws Grizzly H0599 User Manual
(14 pages)
(14 pages)
Power saws Grizzly G9906 User Manual
(14 pages)
(14 pages)
Power saws Grizzly G0575 User Manual
(3 pages)
(3 pages)
© 2020, manymanuals.com. All rights reserved. | 0.767 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals