Grizzly 12" Jointer w/spiral cutterhead manual insert User Manual Page 58
- Page / 73
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
G0609 12" Parallelogram Jointer
-43-
Inspect the V-belts closely; if you notice fraying,
cracking, glazing, or any other damage, replace
the belts. A worn or damaged V-belt will not pro
-
vide optimum power transmission from the motor
to the drum and feed belt.
V-belt removal and replacement is simply a mat
-
ter of loosening the V-belts, rolling them off of
the pulleys, replacing them with new belts, then
retensioning them.
Tools Needed: Qty
Wrench or Socket
19mm ................................... 1
To replace the V-belts
:
1. DISCONNECT JOINTER FROM POWER
SOURCE!
2. Open the pulley cover.
3. Loosen the fasteners on the tension rod that
hold the motor to the bracket (
Figure 61).
V-Belts
Figure 61. Fasteners needed to be loosened for
V-belt replacement.
Tension
Rod
4. Lift the motor up and slide the V-belts off of
the motor pulley and cutterhead pulley.
5. Slide the new belts onto the pulleys, tighten
the motor bracket fasteners, and close the
pulley cover.
Pulley Alignment
Pulley alignment is another important factor in
power transmission and belt life. The pulleys
should be parallel to each other and in the same
plane (coplaner) for optimum performance.
Each pulley can be adjusted by loosening the
motor mount fasteners, sliding the motor in or out,
and retightening the fasteners to lock the motor
pulley in place.
Tools Needed: Qty
Wrench or Socket
17mm ................................... 1
To align the pulleys
:
1. DISCONNECT JOINTER FROM POWER
SOURCE!
2. Open the pulley cover.
3. Visually check the alignment of the two pul-
leys to make sure that they are aligned and
that the V-belts are straight up and down (see
Figure 62).
— If the pulleys are aligned, tighten the motor
mounts and go to Step 8.
— If the pulleys are NOT aligned, do Steps 4
& 5
.
Figure 62. Pulleys aligned.
Cutterhead
Pulley
Motor
Pulley
Fasteners
- MODEL G0609X 1
- 12" JOINTER 1
- 3
- G0609X 220V Wiring Diagram 4
- Jointer Breakdown 5
- Jointer Breakdown Parts List 6
- Tables Breakdown 7
- Fence Breakdown 8
- Stand Breakdown 9
- Stand Parts List 10
- Labels Breakdown 11
- G0609X ACCESSORIES 12
- MODEL G0609 13
- 12" PARALLELOGRAM 14
- Table of Contents 16
- INTRODUCTION 18
- MACHINE DATA 19
- Identification 21
- 22
- SECTION 1: SAFETY 22
- 8" 24
- 220V Single-Phase 25
- SECTION 3: SET UP 26
- Inventory 27
- Hardware Recognition Chart 28
- Site ConsiderationsClean Up 29
- Moving & Placing 30
- Mounting to Shop 30
- Pedestal Switch 32
- Winding Cutterhead 32
- Knife Setting Jig 33
- Checking Outfeed 33
- Table Height 33
- Dust Port 34
- Test Run 34
- SECTION 4: OPERATIONS 35
- Stock Inspection 36
- Squaring Stock 37
- Surface Planing 38
- Edge Jointing 39
- Bevel Cutting 40
- Rabbet Cutting 41
- SECTION 5: ACCESSORIES 42
- SECTION 6: MAINTENANCE 45
- Maintenance Log 46
- SECTION 7: SERVICE 47
- 16" per 48
- Adjusting/Replacing 49
- Inspecting Knives 49
- Checking/Adjusting 52
- Table Parallelism 52
- Adjusting Table Parallelism 53
- Checking Infeed Table 53
- Setting Outfeed 54
- Setting Infeed Table 55
- Calibrating Depth 56
- Pulley Alignment 58
- G0609 Electrical Components 60
- G0609 Wiring Diagram 61
- Base Assembly Parts Breakdown 62
- Base Parts List 63
- Table Parts List 64
- Fence Parts List 65
- Warning Label Parts List 68
- WARRANTY AND RETURNS 69
- 70
- 71
- 73
- 73
Related products and manuals for Tools Grizzly 12" Jointer w/spiral cutterhead manual insert
Tools Grizzly H7677 User Manual
(20 pages)
(20 pages)
Tools Grizzly H6143 User Manual
(20 pages)
(20 pages)
Tools Grizzly G0552 User Manual
(2 pages)
(2 pages)
Tools Grizzly G0677 User Manual
(18 pages)
(18 pages)
Tools Grizzly G9972Z User Manual
(15 pages)
(15 pages)
Tools Grizzly H5529 User Manual
(2 pages)
(2 pages)
Tools Grizzly 230V User Manual
(20 pages)
(20 pages)
Tools Grizzly H7758/H7759 User Manual
(28 pages)
(28 pages)
Tools Grizzly H0801 1800W User Manual
(6 pages)
(6 pages)
Tools Grizzly G6049 User Manual
(17 pages)
(17 pages)
Tools Grizzly G1370 User Manual
(2 pages)
(2 pages)
Tools Grizzly G1200 User Manual
(3 pages)
(3 pages)
Tools Grizzly H8231 User Manual
(2 pages)
(2 pages)
Tools Grizzly G5979 User Manual
(32 pages)
(32 pages)
© 2020, manymanuals.com. All rights reserved. | 1.400 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals