MODEL G7945/46RADIAL DRILL PRESSOWNER'S MANUALG7945G7946COPYRIGHT © JANUARY, 2001 BY GRIZZLY INDUSTRIAL, INC. REVISED FEBRUARY, 2008 (BL)WARNING
-8-G7945/G7946 Radial Drill Press10IdentificationFigure 1. Right-side controls.Figure 2. Left-side controls.Refer to the list below and see Figures 1
G7945/G7946 Radial Drill Press-9-4. ALWAYS USE HEARING PROTECTION WHEN OPERATING MACHINERY. Machinery noise can cause permanent hearing dama
-10-G7945/G7946 Radial Drill Press7. ONLY ALLOW TRAINED AND PROP-ERLY SUPERVISED PERSONNEL TO OPERATE MACHINERY. Make sure oper-ation instruc
G7945/G7946 Radial Drill Press-11-1. EYE/FACE/HAND PROTECTION. A face shield used with safety glasses is rec-ommended. Always keep hands
-12-G7945/G7946 Radial Drill PressFigure 3. Typical type 5-15 plug and receptacle.Serious personal injury could occur if you connect the machi
G7945/G7946 Radial Drill Press-13-The Model G7945/G7946 was carefully packed when it left our warehouse. If you discover the machine is
-14-G7945/G7946 Radial Drill PressFigure 5. G7946 layout.Figure 4. G7945 layout.Description Qty1. Headstock ...
G7945/G7946 Radial Drill Press-15-Hardware Recognition Chart
-16-G7945/G7946 Radial Drill PressThe unpainted surfaces are coated with a waxy oil to protect them from corrosion during ship-ment. Remove th
G7945/G7946 Radial Drill Press-17-Table BracketComponents and Hardware Needed: QtyTable ...
-18-G7945/G7946 Radial Drill PressFigure 9. Rack orientation (G7946 shown).Figure 10. Inside bevel in the correct position.Crank HandleColumn RingSet
G7945/G7946 Radial Drill Press-19-The drill chuck is attached to the drill spindle by means of a machined taper between the chuck and spindle n
-20-G7945/G7946 Radial Drill PressTest RunWear safety glasses whenever starting or using machine. Failure to comply may result in serious pe
G7945/G7946 Radial Drill Press-21-Floor MountingOnce you have confirmed that your Model G7946 is running properly, we strongly recommend mounting
-22-G7945/G7946 Radial Drill PressFor your convenience, the adjustments listed below have been performed at the factory; how-ever, because of
G7945/G7946 Radial Drill Press-23-Loose hair and cloth-ing could get caught in machinery and cause seri-ous personal injury. Keep loose clothi
-24-G7945/G7946 Radial Drill PressChoosing SpeedsTwist/Brad Point Drill BitsSoft WoodHard WoodPlasticBrassAluminumMild Steel1/16" – 3/16" 30
G7945/G7946 Radial Drill Press-25-Never operate drill press with pulley cover in the open position. Your hand may become trapped in the belt
-26-G7945/G7946 Radial Drill PressThe Model G7945/G7946 is designed for drilling holes in wood or metal. The basic operation of a drill pres
G7945/G7946 Radial Drill Press-27-Figure 22. Depth stop components.Depth NutJam NutDepth Stop StudThe Model G7945/G7946 has a depth stop that all
Table of ContentsINTRODUCTION ...
-28-G7945/G7946 Radial Drill PressFigure 24. Locating pin and nut (G7946). 2. Loosen the lock bolt (Figure 25) using the included wrench and
G7945/G7946 Radial Drill Press-29-Head AdjustmentsFigure 27. Lock pin location.The headstock can be tilted from 45° clockwise to 90° counterclockwise.
-30-G7945/G7946 Radial Drill PressSECTION 5: ACCESSORIESFigure 30. Model G8581 1⁄2" Keyless Drill Chuck JT #33.G8581—1⁄2" Keyless Drill Chuc
G7945/G7946 Radial Drill Press-31-Figure 34. Model G8865 13-PC Alloy Drill Bits.G8865—Cobalt Alloy Drill Bits 13-PC. Set G8866—Steelex® Cobalt Alloy D
-32-G7945/G7946 Radial Drill PressAlways disconnect power to the machine before performing maintenance. Failure to do this may result in serio
G7945/G7946 Radial Drill Press-33-Review the troubleshooting and procedures in this section to fix your machine if a problem develops. If you need rep
-34-G7945/G7946 Radial Drill PressSymptom Possible Cause Possible SolutionMachine has vibration or noisy operation. 1. Motor or component is loose.2.
G7945/G7946 Radial Drill Press-35-Figure 36. Depth stop assembly.Calibration NutReturn Height NutStopBracketThe drill press comes fitted with a
-36-G7945/G7946 Radial Drill PressElectrical ComponentsFigure 40. Motor wiring.To PowerPower SwitchFigure 39. Power switch wiring.MotorCapacitorGround
G7945/G7946 Radial Drill Press-37-
SECTION 7: SERVICE ... 33About Service
-38-G7945/G7946 Radial Drill PressG7945/G7946 Parts Breakdown434739375150444845A59603231462734362828-128294241403320101101656654110385322231153619B564
G7945/G7946 Radial Drill Press-39-REF PART # DESCRIPTION REF PART # DESCRIPTION8 P7945008 GEAR 45A-1 P7945045A-1 DEPTH STOP ROD V2.02.059 PR16M EXT RE
-40-G7945/G7946 Radial Drill PressG7945 Parts Breakdown34578717374707272-1807379793-1113112117-183123
G7945/G7946 Radial Drill Press-41-REF PART # DESCRIPTION REF PART # DESCRIPTION1 P7945001 BASE 72-1 P7945072-1 CRANK HANDLE3 PB09M HEX BOLT M8-1.25 X
-42-G7945/G7946 Radial Drill PressG7946 Parts Breakdown1717374707272-14A-18412712896129111184A80737313834123927-19793-1
G7945/G7946 Radial Drill Press-43-REF PART # DESCRIPTION REF PART # DESCRIPTION1 P7946001 BASE V2.04.03 74 P7946074 WORM GEAR3 PB31M HEX BOLT M10-1.5
-44-G7945/G7946 Radial Drill PressSafety Label Placement and Parts ListSafety Label PlacementThe safety labels on this machine warn and indicate how t
G7945/G7946 Radial Drill Press-45-Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the d
G7945/G7946 Radial Drill Press-3-If you have any comments regarding this manual, please write to us at the address below:Grizzly Industrial, Inc.C/O T
-4-G7945/G7946 Radial Drill PressThe information contained herein is deemed accurate as of 11/25/2005 and represents our most recent product specifica
G7945/G7946 Radial Drill Press-5-The information contained herein is deemed accurate as of 11/25/2005 and represents our most recent product specifica
-6-G7945/G7946 Radial Drill PressThe information contained herein is deemed accurate as of 11/25/2005 and represents our most recent product specifica
G7945/G7946 Radial Drill Press-7-The information contained herein is deemed accurate as of 11/25/2005 and represents our most recent product specifica
Comments to this Manuals