Grizzly G0605X User Manual Page 23
- Page / 76
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
G0605X/G0606X Extreme Series 12" Table Saw
-21-
Outfeed Table
Components and Hardware Needed: Qty
Outfeed Table
.................................................... 1
Lower Shelf ........................................................
1
Shelf End Plate ..................................................
1
Support Legs .....................................................
2
Lower Shelf Brackets ........................................
2
Fence Tube ........................................................
1
Flange Bolts M8-1.25 x 16 ................................
2
Hex Bolts M6-1 x 12 ..........................................
4
Phillips Head Screws M6-1 x 12 .....................
12
Feet
3
⁄8-16 x 2 .................................................... 2
Hex Nuts M6-1 ..................................................
2
Hex Nuts M8-1.25 .............................................
2
Hex Nuts
3
⁄8-16 .................................................. 2
Flat Washers 6mm .......................................... 16
Flange Bolts M8-1.25 x 12 ................................ 9
To install the outfeed table:
1. Turn the outfeed table upside down and
place it on a level surface.
2. Install the feet, support legs, and shelf end
plate in the same manner as described in
Extension Table instructions.
11. Fasten each support leg to the main exten-
sion table with four Phillips head screws and
flat washers as shown in
Figure 19.
Figure 19. Support leg fastened to main
extension table.
12. Rotate both feet until they touch the ground,
and tighten the hex nuts to secure the feet.
13. Fasten the shelf end plate to the legs with
four Phillips head screws and flat washers as
shown in
Figure 20.
14. Place the shelf brackets between the cabinet
and support legs, and fasten with four M6-1
x 12 hex bolts, four flat washers and two hex
nuts (on the outside) as shown in
Figure 21.
Note:
The flange on the shelf bracket must point
up to ensure proper installation.
15. Place the lower shelf on the brackets.
Figure 20. Installing shelf end plate on extension
table legs.
Figure 21. Shelf brackets installed.
Shelf Bracket
Flange
- MODEL G0605X/G0606X 1
- EXTREME SERIES 1
- 12" TABLE SAW 1
- Table of Contents 3
- INTRODUCTION 5
- MACHINE DATA 6
- Identification 8
- SECTION 1: SAFETY 9
- Protecting Yourself 12
- From Kickback 12
- Preventing Kickback 12
- Glossary of Terms 13
- Operation 14
- Extension Cords 15
- Grounding 15
- SECTION 3: SET UP 16
- Machine Inventory 17
- Fence Inventory 17
- Fence Rail Inventory 17
- Outfeed Table 18
- Inventory 18
- Extension Table 18
- Hardware Recognition Chart 19
- Site ConsiderationsClean Up 20
- Support Leg 22
- Saw Blade 24
- Front Of Saw 24
- Teeth Direction 24
- & Blade Rotation 24
- Table Insert 25
- Blade Guard and 25
- Splitter 25
- Riving Knife 26
- On/Off Switch 26
- Miter Gauge 27
- Fence Components 27
- Flange Bolt 27
- Anti-Start 27
- Safety Pin 27
- Recommended 28
- Adjustments 28
- Dust Collection 28
- Test Run 28
- SECTION 4: OPERATIONS 30
- Disabling On/Off 31
- Blade Selection 31
- Non-Through and 33
- Through Cuts 33
- Crosscutting 34
- Miter Cuts 35
- Blade Tilt/Bevel Cuts 35
- Dado Cutting 36
- 38
- Resawing 40
- Auxiliary Fence 41
- Resawing Operations 41
- 8" 42
- SECTION 5: ACCESSORIES 43
- SECTION 6: MAINTENANCE 46
- SECTION 7: SERVICE 47
- Table Saw Operations 48
- Blade Tilt Stops 51
- Digital Readout 52
- Miter Slot to Blade 53
- Parallelism 53
- Blade Alignment 55
- Adjusting Fence 55
- Service Log 57
- G0605X Wiring Diagram 59
- G0606X Electrical Components 60
- G0606X Wiring Diagram 220V 61
- G0606X Wiring Diagram 440V 62
- WARRANTY AND RETURNS 72
- 73
- 74
- 76
- 76
Related products and manuals for Power saws Grizzly G0605X
Power saws Grizzly G0668 User Manual
(2 pages)
(2 pages)
Power saws Grizzly G0681 9 User Manual
(4 pages)
(4 pages)
Power saws Grizzly G0696X User Manual
(101 pages)
(101 pages)
Power saws Grizzly G9744Z User Manual
(52 pages)
(52 pages)
Power saws Grizzly ZX3 User Manual
(63 pages)
(63 pages)
Power saws Grizzly H0601 User Manual
(14 pages)
(14 pages)
Power saws Grizzly Model G0536 User Manual
(31 pages)
(31 pages)
Power saws Grizzly H6548 User Manual
(2 pages)
(2 pages)
Power saws Grizzly G1148 User Manual
(28 pages)
(28 pages)
Power saws Grizzly G1011Z User Manual
(41 pages)
(41 pages)
Power saws Grizzly G1129 User Manual
(39 pages)
(39 pages)
Power saws Grizzly G0493 User Manual
(104 pages)
(104 pages)
Power saws Grizzly H6246 User Manual
(40 pages)
(40 pages)
Power saws Grizzly G4818 User Manual
(1 pages)
(1 pages)
© 2020, manymanuals.com. All rights reserved. | 0.678 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals